Countryman Associates, Inc.
Wireless Transmitter Wiring
1. For E6 with Duramax 2mm cable, substitute RED for WHITE
2. For E6 with Duramax 2mm cable, clip the BLACK wire.
3. The table below does not apply to E2 Earsets or B2D Lavaliers. Please refer to the price list or the corresponding product pages for compatibility information.
| Brand | Code | Model | Connector | E6/B6/H6 | B3 | EMW | ISOMAX 2 | |
|---|---|---|---|---|---|---|---|---|
| AKG | AG | PT51, PT300, PT900 | AKG B-LOC (3.5mm locking male thread) | Sleeve = S Tip = W 10k ohms Tip to Sleeve 5V Zener Diode stripe end to tip other end to sleeve diagram |
Sleeve = S+B Tip = R diagram |
Sleeve = S+B Tip = R diagram |
Sleeve = S+B Tip = R Use W3 type headset diagram |
|
| AKG | AK | PT40, PT45, PT60, PT61, PT80, PT81, PT400, PT450, PT2000, PT4000 | TA3F | Pin 1= S Pin 3 = W Jumper 2 to 3 1 to 2 = 6.8k ohms 200pF capacitor Pin 1 to Pin 3 diagram |
Pin 1= S+B Pin 2 = R Jumper 2 to 3 diagram |
Pin 1 = S + B Pin 2 = R Jumper 2 to 3 diagram |
Pin 1 = S+B Pin 2 = R Jumper 2 to 3 Use W3 type headset diagram |
|
| Amplivox | AM | S-1600T | 3.5mm non-locking mono plug | Sleeve = S Tip = W Jumper ring to tip 5V Zener Diode + to tip - to sleeve diagram |
Sleeve = S+B Tip = R Jumper ring to tip diagram |
Sleeve = S+B Tip = R Jumper ring to tip diagram |
Sleeve = S+B Tip = R Jumper ring to tip Use W3 type headset diagram |
|
| Anchor Audio | AA | WB-6000, WB-6400 | TA4F | Pin 1 = S Pin 2 = W 1k ohms 3 to 2 diagram |
Pin 1 = S+B Pin 2 = R 1k ohms 3 to 2 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R 10k ohms 1 to 2 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R 10k ohms 1 to 2 Use W5 type headset diagram |
|
| Audio 2000's | SR | AWX6030M | 3.5mm locking plug | Sleeve = S Tip = W Jumper ring to sleeve 5V Zener Diode + to tip - to sleeve diagram |
Sleeve = S+B Tip = R Jumper ring to sleeve diagram |
Sleeve = S 6.8k resistor B to Sleeve Tip = R Jumper ring to sleeve diagram |
Sleeve = S+B Tip = R Jumper ring to sleeve Use W3 type headset diagram |
|
| Audio Limited | AL | TX 2000, RMS-2000-mxl | Lemo 6-pin (FFA.2C.306) | Pin 1 = W Pin 5 = S Jumper 1 to 2 Jumper 3 to 4 5V Zener Diode + to 5, - to 1 diagram |
Pin1 = R Pin5 = S + B Jumper 1 to 2 Jumper 3 to 4 diagram |
Pin1 = B Pin 3 = R Pin 5 = S Jumper 1 to 6 Jumper 3 to 4 diagram |
Pin 1 = B Pin 3 = R Pin 5 = S Jumper 1 to 6 Jumper 3 to 4 Use W5 type headset diagram |
|
| Audio Technica | AN | T35, T75, T211, T601, T701, T1000a, 1000 Series, 1200 Series, 4000 Series, 5000 Series, 7000 Series, T1001 | Hirose 4-pin HR10A-7P-4S | Jumper 1 to 2 Pin 1 = S Pin 3 = W 15k ohms 3 to 4 diagram |
Jumper 1 to 2 Pin 1 = S + B Pin 3 = R 10k ohms 3 to 4 diagram |
Jumper 1 to 2 Pin 1 = S Pin 3 = B Pin 4 = R diagram |
Jumper 1 to 2 Pin 1 = S Pin 3 = B Pin 4 = R Use W5 type headset diagram |
|
| Audio Technica | AT | T27, T31, T51, T200, T201, T210, T210a, T300, T310, T310b, 1100 Series, 1400 Series, 2000 Series, 3000 Series, T1801, T801 | Hirose 4-pin HR10A-7P-4S | Pin 1 = S Pin 3 = W Jumper 1 to 2 2.7k ohms 3 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 Use W5 type headset diagram |
|
| Audio Technica | AW | ATW-U101 | TA5F | Pin 1 = S Pin 3 = W Jumper 2 to 4 4.7k ohms 1 to 3 diagram |
Pin 1 = S + B Pin 3 = R Jumper 2 to 4 diagram |
Pin 1 = S + B Pin 3 = R Jumper 2 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 2 = R Use W5 type headset diagram |
|
| Audix | AD | 360 | TA3F | Pin 1 = S Pin 2 = W 6.8k ohms 2 to 3 diagram |
Pin 1 = S+B Pin 2 = R 6.8k ohms 2 to 3 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R 10k ohms 1 to 2 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R 10k ohms 1 to 2 Use W5 type headset diagram |
|
| Azden | ZP | WM-PRO, WLT-PRO, 32BT, 31LT | 3.5mm non-locking mono plug | Sleeve = S Tip = w 6.8k ohms T to S 5V Zener Diode stripe end to tip other end to sleeve diagram |
Tip = R Sleeve = S+B diagram |
Tip = R Sleeve = S+B diagram |
Tip = R Sleeve = S+B Use W4 type headset diagram |
|
| Azden | ZU | 41BT (UHF) | Hirose 4 pin HR10A-7P-4P | Pin 4 = S Pin 1 = W 10k ohms 1 to 3 diagram |
Pin 4 = S + B Pin 1 = R Jumper 1 to 3 diagram |
Pin 4 = S Pin 1 = B Pin 3 = R 10k ohms 1 to 4 diagram |
Pin 4 = S Pin 1 = B Pin 3 = R 10k ohms 1 to 4 Use W5 type headset diagram |
|
| Azden | ZV | Older 41BT, 10BT | 3.5mm locking plug | Sleeve = S Tip = w 2.7k ohms T to S 5V Zener Diode stripe end to tip other end to sleeve diagram |
Sleeve = S+B Tip = R diagram |
Sleeve = S+B Tip = R diagram |
Sleeve = S+B Tip = R use W3 type headset diagram |
|
| Beyer | BS | TS-170, TS-170p, TS-190 | Lemo type S 4-pin | Pin 2 = S Pin 1 = W 10k ohms 1 to 3 diagram |
Pin 2 = S + B Pin 4 = R diagram |
Pin 1 = B Pin 2 = S Pin 3 = R diagram |
Pin 1 = B Pin 2 = S Pin 3 = R use w5 type headset diagram |
|
| Beyer | BT | TS-300, TS-400, TS-600 | Lemo type S 4-pin | Pin 1 = S Pin 4 = W 10k ohms 2 to 4 diagram |
Pin 1 = S+B Pin 3 = R diagram |
Pin 1 = S Pin 2 = R Pin 4 = B 10k ohms 1 to 4 diagram |
Pin 1 = S Pin 2 = R Pin 4 = B 10k ohms 1 to 4 Use W5 type headset diagram |
|
| Beyer | MI | Opus Series, TS-100, TS-300, TS-500, TS-800 | Screw on TA4F | Pin 1 = S Pin 3 = W Jumper 2 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 Use W5 headset diagram |
|
| CAD Audio | CA | WX155A (100 System) | TA4F | Pin 1 = S Pin 3 = W Jumper 2 to 1 5.6k resistor, Pin 4 to Pin 3 5V Zener diode, stripe end to Pin 3, other end to Pin 1 diagram |
Pin 1 = B+S Pin 3 = R Jumper 2 to 1 5.6k resistor, Pin 4 to Pin 3 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 Use W5 type headset diagram |
|
| CAD Audio | CD | WL-200P (1200 System) | TA4F | Pin 1 = S Pin 3 = W Jumper 2 to 1 15k resistor, Pin 4 to Pin 3 5V Zener diode, stripe end to Pin 3, other end to Pin 1 diagram |
Pin 1 = B+S Pin 3 = R Jumper 2 to 1 15k resistor, Pin 4 to Pin 3 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 Use W5 type headset diagram |
|
| Carvin | SL | UX16-BP | TA4F | Pin1 = S Pin3 = W 4.7k pin 2 to Pin 3 5V Zener Diode stripe end to Pin 3 other end to Pin 1 diagram |
Pin1 = S+B Pin3 = R 10k ohms 2 to 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin1 to pin 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin 1 to pin 3 Use W5 type headset diagram |
|
| Comtek | CL | Lemo type S 4-pin | Pin 1 = S Pin 2 = W 6.8k ohms 2 to 3 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R Jumper 1 to 4 diagram |
||||
| Comtek | C2 | M-216 | Switchcraft 851 | Sleeve = S Tip = W diagram |
Sleeve = B+S Tip = R diagram |
Sleeve = B+S Tip = R diagram |
Sleeve = B+S Tip = R Use W3 Type Headset diagram |
|
| Comtek | CS | TA4M | Pin 1 = S Pin 2 = W 4.7k ohms 2 to 3 diagram |
|||||
| Comtek | SD | 3.5mm | ||||||
| Electrovoice | EM | RTM-1 | Lemo 4 pin | 6.8k ohms 2 to 3 Pin1 = S Pin2 = W diagram |
10k ohms 2 to 3 Pin 1 = S+B Pin 2 = R diagram |
Pin 1 = S Pin 2 = B Pin 3 = R diagram |
Pin 1 = S Pin 2 = B Pin 3 = R diagram |
|
| Electrovoice | ET | 3000 Series, N/DYM NBPU, MSB, BPV, BPU, BPU2, CSB-1000, RE-1, RE-2, BP-300 | TA4F | 6.8k ohms 2 to 3 Pin 1 = S Pin 2 = W diagram |
10k ohms 2 to 3 Pin 1 = S+B Pin 2 = R diagram |
Pin 1 = S Pin 2 = B Pin 3 = R 10k ohms1 to 2 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R 10k ohms1 to 2 diagram |
|
| Electrovoice | EV | 2000 Series, 2500 Series | TA4F | Jumper 2 to 3 Pin 3 = W Pin 4 = S diagram |
Pin 2 = R Pin 4 = S+B diagram |
Pin 1 = R Pin 3 = B Pin 4 = S 10k ohms 3 to 4 diagram |
Pin 1 = R Pin 3 =B Pin 4 = S 10k ohms 3 to 4 diagram |
|
| Fender | FN | Passport | Mini 4 pin | Pin 1 = S Pin 3 = W Jumper 2 to 4 diagram |
Pin 1 = S+B Pin 2 = R Jumper 2 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
|
| Gemini | TA3F | Pin 1 = S Pin 2 = W 10k ohms 2 to 3 | ||||||
| HME | HS | TX550, TX822 | TA4F | Pin 1 = S Pin 2 = W 10k ohms 2 to 3 diagram |
Pin 1 = S+B Pin 2 = R 10 k ohms 2 to 3 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R diagram |
Pin 1 = S Pin 2 = B Pin 3 = R diagram |
|
| JTS | SL | All with TA4F connector | TA4F | Pin1 = S Pin3 = W 4.7k pin 2 to Pin 3 5V Zener Diode stripe end to Pin 3 other end to Pin 1 diagram |
Pin1 = S+B Pin3 = R 10k ohms 2 to 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin1 to pin 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin 1 to pin 3 Use W5 type headset diagram |
|
| Lectrosonics | L2 | M170, M175 | Switchcraft 851 | Tip = W Sleeve = S 10k ohms tip to sleeve diagram |
Tip = R Sleeve = S+B diagram |
Tip = R Sleeve = S+B diagram |
Tip = R Sleeve = S+B Use W4 type headset diagram |
|
| Lectrosonics | L4 | UM Series, LM Series |
TA5F | Pin 1 = S 1.5k ohm Pin 2 to 3 3.3k pin 3 to white Crimp fingers to shield diagram |
Pin 1 = S+B Pin 3 = R Jumper 2 to 4 Crimp fingers to shield diagram |
Pin 1 = S+B Pin 3 = R Jumper 2 to 4 Crimp fingers to shield diagram |
Pin 1 = S Pin 2 = R Pin 3 = B Jumper 1 to 4 C201 1 to 2 C201 3 to 4 Crimp fingers to shield Use W5 type headset diagram |
|
| Lectrosonics | LE | H Series | Switchcraft A3M | Jumper 1 to Shell Pin 1 = S 10K Pin 2 to W 1uF Pin 2 to W diagram |
Jumper 1 to Shell Pin 1 = S+B Pin 2 = R diagram |
Jumper 1 to Shell Pin 1 = S+B Pin 2 = R diagram |
Jumper 1 to Shell Pin 1 = S+B Pin 2 = R Use W4 type headset diagram |
|
| Lectrosonics | LS | M Series over 185 | TA5F | Pin 1 = S 1.5k ohm Pin 2 to 3 3.3k pin 3 to white diagram |
Pin 1 = S+B Pin 3 = R Jumper 2 to 4 diagram |
Pin 1 = S+B Pin 3 = R Jumper 2 to 4 diagram |
Pin 1 = S Pin 2 = R Pin 3 = B Jumper 1 to 4 C201 1 to 2 C201 3 to 4 Use W5 type headset diagram |
|
| Lectrosonics | LW | MM400
**See additional information |
Waterproof 2.5mm | Tip = W Sleeve = S 2.7k ohms tip to sleeve 5V Zener Diode + to tip - to sleeve diagram |
Tip = R Sleeve = S 10k B to Sleeve diagram |
Tip = R Sleeve = S 10k B to Sleeve diagram |
Tip = R Sleeve = S 10k B to Sleeve Use W4 type headset diagram |
|
| Lectrosonics | WM | WM
**See additional information |
Waterproof 2.5mm | Tip = W Sleeve = S 5.1V Zener from Sleeve to Tip (striped end to Tip) diagram |
Tip = R Sleeve = S + B diagram |
Tip = R Sleeve = S + B diagram |
1.8k from Tip to R Sleeve = S + B Use W3 type headset diagram |
|
| Lectrosonics | LX | UH Series | Switchcraft A3M | Pin 1 = S 10K Pin 2 to W 1uF Pin 2 to W Connect shield to XLR shell diagram |
Pin 1 = S+B Pin 2 = R Connect shield to XLR shell diagram |
Pin 1 = S+B Pin 2 = R Connect shield to XLR shell diagram |
Pin 1 = S+B Pin 2 = R Use W4 type headset Connect shield to XLR shell diagram |
|
| Lectrosonics | SM | SM Series, UMa Series, LMa Series | TA5F | Pin 1 = S pin 3 to white diagram |
Pin 1 = S+B Pin 3 = R Jumper 2 to 4 diagram |
Pin 1 = S+B Pin 3 = R Jumper 2 to 4 diagram |
Pin 1 = S+B Jumper Pin 2 to Pin 4 Pin 3 = 1.8k to R Use W3 type headset diagram |
|
| Lightspeed | LH | BP-200 | Hirose 4-pin HR10A-7P-4S | Pin 1 = S Pin 3 = W 10k ohms Pin 3 to 4 Jumper Pin 1 to 2 diagram |
Pin 1 = S+B Pin 3 = W 10k ohms Pin 3 to 4 Jumper Pin 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Use W5 type headset diagram |
|
| Lightspeed | LT | BP-700, BP-800, BP-900 | TA4F | Pin 1 = S Pin 3 = W Jumper 1 to 2 12K ohms 3 to 4 diagram |
Pin 1 = S+B Pin 3 = R Jumper 1 to 2 12K ohms 3 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 10k ohms 1 to 3 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 10k ohms 1 to 3 Use W5 type headset diagram |
|
| Line 6 | L3 | XD-V30L, XD-V35, Relay G30 | 1/4 in Right Angle Phone Plug | Sleeve = S Tip = W jumper tip to ring 5V Zener Diode stripe end to tip other end to sleeve diagram | Sleeve = S+B Tip = R jumper ring to tip diagram |
Sleeve = S Tip = B Ring = R 22k ohms tip to sleeve diagram |
Sleeve = S Tip = B Ring = R 22k ohms tip to sleeve Use W5 type headset diagram |
|
| Line 6 | L7 | XD-V55, XD-V70, XD-V75, Relay G50, Relay G55, Relay G90 | TA4F | Pin1 = S Pin3 = W 4.7k pin 2 to Pin 3 5V Zener Diode stripe end to Pin 3 other end to Pin 1 diagram |
Pin1 = S+B Pin3 = R 10k ohms 2 to 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin1 to pin 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin 1 to pin 3 Use W5 type headset diagram |
|
| Listen Technologies | T7 | LT-700 | 3.5mm stereo non-locking plug | Tip = W, Sleeve = S, Ring = Open, 5.1V Zener stripe end towards tip diagram |
Tip = R, Sleeve = B+S, Ring = Open diagram |
Tip = R, Sleeve = B+S, Ring = Open diagram |
Tip = R, Sleeve = B+S, Ring = Open, Use W3 type headset diagram |
|
| Micron | M7 | TX 700.xx (negative ground) | Lemo 6 pin | Pin 1 = W Pin 5 = S Jumper 4 to 5 6.8k ohms 1 to 6 Zener diode (5.1V) 5 to 1 diagram |
Pin 1 = R Pin 5 = S+B Jumper 4 to 5 Jumper 1 to 6 diagram |
Pin 1 = B Pin 5 = S Pin 6 = R Jumper 4 to 5 10k ohms 1 to 5 diagram |
Pin 1 = B Pin 5 = S Pin 6 = R Jumper 4 to 5 10k ohms 1 to 5 Use W5 type headset diagram |
|
| Micron | MC | TX 101, TX 102, TX 501, TX 502 (Older Positive Ground Types) | Lemo 8 pin FFA.2C.308.CLA Caution: the pin numbering on these connectors is inconsistant |
(Micron Pin Numbers) Pin 8 = S Pin 3 = W 15k ohms 3 to 4 Jumper 5 to 6 diagram |
(Micron Pin Numbers) Pin 8 = S+B Pin 3 = R 10k ohms 3 to 4 Jumper 5 to 6 diagram |
Pin 8 = S Pin 7 = B Pin 6 = R Jumper 5 to 6 diagram |
Pin 8 = S Pin 7 = B Pin 6 = R Jumper 5 to 6 Use W5 type headset diagram |
|
| Micron | MX | TX 500.xx (negative ground) | Lemo 8 pin FFA.2C.308.CLA Caution: the pin numbering on these connectors is inconsistant |
Pin 6 = S Pin 1 = W 6.8K ohms 1 to 8 Jumper 5 to 6 diagram |
Pin 6 = S+B Pin 1 = R 6.8K ohms 1 to 8 Jumper 5 to 6 diagram |
Pin 6 = S Pin 8 = R Pin 3 = B Jumper 5 to 6 diagram |
Pin 6 = S Pin 8 = R Pin 3 = B Jumper 5 to 6 Use W5 type headset diagram |
|
| Mipro | MI | ACT-707-TS (TE), ACT-801 TS (TE), MT103, MT303, MT801, MT808, ACT-30T, ACT-50T, ACT-7T(A) | Screw on TA4F | Pin 1 = S Pin 3 = W Jumper 2 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 Use W5 headset diagram |
|
| Mipro | MN | Mipro Transmitters with special screw-on mini 4-pin (not TA-4F) | Mini Mipro 4 pin | Pin 1 = S Pin 3 = W Jumper 2 to 4 diagram |
Pin 1 = S+B Pin 2 = R Jumper 3 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 Use W5 Type Headset diagram |
||
| Nady | Lemo 4 pin | Pin 1 = R Pin 2 to 1 22k ohms Pin 3 is S+B | Pin 1 = B Pin 2 = R Pin 4 = S | Pin 1 = B Pin 2 = Red Pin 3 = S Use W5 Type Headset | ||||
| Nady | NS | TA3F | Pin 1 = S Pin 3 = W 6.8k ohms/ 2 to 3 diagram |
Pin 1 = S + B Pin 3 = R 10k ohms 2 to 3 diagram |
Pin 1 = S Pin 2 = R Pin 3 = B diagram |
Pin 1 = S Pin 2 = R Pin 3 = B Use W5 type headset diagram |
||
| Nady | NL | UB10, UB16, WLT14, WLT15 | 3.5mm locking plug | Sleeve = S Tip = W diagram |
Sleeve = S+B Tip = R diagram |
Sleeve = S+B Tip = R diagram |
Sleeve = S+B Tip = R Use W3 Type Headset diagram |
|
| Paso | PA | MW 163, 223, 293, 323 | TA4F | Pin 1 = S, Pin 3 = W, Jumper Pin 1 to Pin 2, 10k Resistor Pin 3 to Pin 4 diagram |
Pin 1 = S+B, Pin 3 = R, Jumper Pin 1 to Pin 2, 10k Resistor Pin 3 to Pin 4 |
Pin 1 = S, Pin 3 = B, Pin 4 = R, Jumper Pin 1 to Pin 2, 22k Resistor Pin 3 to Pin 1 |
Pin 1 = S, Pin 3 = B, Pin 4 = R, Jumper Pin 1 to Pin 2, 22k Resistor Pin 3 to Pin 1, Use W5 Type Headset |
|
| Peavey | MI | PCX-V12-B, PCX-U302-B | TA4F | Pin 1 = S Pin 3 = W Jumper 2 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 Use W5 headset diagram |
|
| Ramsa | RB300, RP410 | Hirose twist lock 4 pin | Pin 1 = W Pin 4 = S 2.7k ohms 1 to 3 C102 1 to 4 | Pin 4 = S Pin 3 = R Pin 2 = B C102 4 to 2 C102 4 to 3 | Pin 4 = S Pin 3 = R Pin 2 = B C102 4 to 2 C102 4 to 3 4.7k ohms in series with black wires | Pin 4 = S Pin 3 = R Pin 2 = B C102 4 to 2 C102 4 to 3 4.7k ohms in series with black Use W5 type Headset | ||
| Relacart | RL | All with TA-4F | TA4F | Pin 1 = S Pin 2 = W 4.7k resistor Pin 2 to Pin 3 5V Zener stripe end to 2 and other end to 1 diagram |
Pin 1 = S+B Pin 2 = R 10k resistor Pin 2 to Pin 3 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R 22k resistor Pin 2 to Pin 1 diagram |
Pin 1 = S + B Pin 2 = B Pin 3 = R 22k resistor Pin 2 to Pin 1 Use W5 type headset |
|
| Revolabs | RV | HD (Countryman Adaptor) | TA4F | Pin 1 = S Pin 3 = W 5V Zener stripe end to 3 and other end to 1 diagram |
Pin 1 = S+B Pin 3 = R diagram |
Pin 1 = S+B Pin 3 = R diagram |
Pin 1 = S + B Pin 3 = R Use W4 type headset diagram |
|
| Sabine | SB | SW16T, SW30T | Sabine mini 4 pin (similar to Mipro & Fender) |
Pin 1 = S Pin 3 = W Jumper 2 to 4 diagram |
Pin 1 = S+B Pin 2 = R Jumper 3 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
|
| Sabine | SS | SW16TX, SW30TX, SW1600, SW3000, ST50T | screw on 4 pin (similar to TA4-F) | Pin 1 = S Pin 3 = W Jumper 2 to 4 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 diagram |
Pin 1 = S Pin 3 = B Pin 4 = R Jumper 1 to 2 Use W5 type headset diagram |
|
| Sabine | ST | SW70, DS80-T | TA4F | Pin 1 = S Pin 3 = W 3.3k ohms 2 to 3 200pF 3 to 1 diagram |
Pin 1 = S Pin 3 = B Pin 2 = R Jumper 3 to 4 200pF capacitor 3 to 1 diagram |
Pin 1 = S Pin 3 = B Pin 2 = R Jumper 3 to 4 200pF capacitor 3 to 1 diagram |
Pin 1 = S Pin 3 = B Pin 2 = R Jumper 3 to 4 200pF capacitor 3 to 1 Use W5 type headset diagram |
|
| Samson | AS | Airline AL-1 | 2.5mm Stereo | Sleeve = S Tip = W Jumper ring to tip 5V Zener Diode + to tip - to sleeve diagram |
Tip = R Jumper Ring to Tip Sleeve = S+B diagram |
Tip = R Jumper Ring to Tip Sleeve = S+B diagram |
||
| Samson | SA | CT2, BT3, UT4, TX3 (Gray) | Hirose 6 pin | Pin 2 = W Pin 6 = S 10k ohms 1 to 2 10k ohms 2 to 6 diagram |
Pin 2 = R Pin 6 = S+B 10k ohms 1 to 2 diagram |
Pin 1 = R Pin 2 = B Pin 6 = S 10k ohms 2 to 6 diagram |
Pin 1 = R Pin 2 = B Pin 6 = S 10k ohms 2 to 6 Use W5 type headset diagram |
|
| Samson | SV | AL-300, CT3, CT7, VT2L, UT1L, T32 | TA3F | Pin 1 = S Pin 3 = W Jumper 2 to 3 4.7k ohms 1 to 2 diagram |
Pin 1 = S+B Pin 3 =R Jumper 2 to 3 diagram |
Pin 1 = S+B Pin 3 =R Jumper 2 to 3 diagram |
Pin 1 = S+B Pin 3 =R Jumper 2 to 3 Use W3 type headset diagram |
|
| Samson | SX | UT5, UT6, TX3 (Black) | Hirose 6 pin | Pin 2 = W Pin 6 = S 10k ohms 1 to 2 10k ohms 2 to 6 diagram |
Pin 2 = R Pin 6 = S+B 10k ohms 1 to 2 diagram |
Pin 1 = R Pin 2 = B Pin 6 = S 10k ohms 2 to 6 diagram |
Pin 1 = R Pin 2 = B Pin 6 = S 10k ohms 2 to 6 Use W5 type headset diagram |
|
| Sennheiser | S1 | BF1083 | Lemo 1 pin | Shell = S Pin = W diagram |
Shell = S+B Pin = R diagram |
Shell = S+B Pin = R diagram |
Shell = S+B Pin = R Use W3 type headset diagram |
|
| Sennheiser | S2 | SK2000, SK9000 | Lemo 3 pin | Jumper 1 to 2 Pin3 = W Pin1 = S diagram |
Jumper 1 to 2 Pin3 = R Pin1 = S+B diagram |
Jumper 1 to 2 Pin3 = R Pin1 = S+B diagram |
Jumper 1 to 2 Pin3 = R Pin1 = S+B Use W3 type headset diagram |
|
| Sennheiser | S3 | SK-50, SK250, SK3063, SK5012, SK5212 |
Lemo 3 pin | Pin3 = W Pin1 = S diagram |
Pin3 = R Pin1 = S+B diagram |
Pin3 = R Pin1 = S+B diagram |
Pin3 = R Pin1 = S+B Use W3 type headset diagram |
|
| Sennheiser | SE | SK2012 | Microdot | Shell = S Pin = W diagram |
Shell = S+B Pin = R diagram |
Shell = S+B Pin = R diagram |
Shell = S+B Pin = R Use W3 type headset diagram |
|
| Sennheiser | SR | Evolution Series, EW100, EW300, EW500, G2, G3**, SK 1093, SK 20 **See additional information |
3.5mm locking plug | Sleeve = S Tip = W Jumper ring to sleeve 5V Zener Diode + to tip - to sleeve diagram |
Sleeve = S+B Tip = R Jumper ring to sleeve diagram |
Sleeve = S 6.8k resistor B to Sleeve Tip = R Jumper ring to sleeve diagram |
Sleeve = S+B Tip = R Jumper ring to sleeve Use W3 type headset diagram |
|
| Sennheiser | S6 | SK2020 Tour Guide System |
3.5mm locking plug | Sleeve = S Tip = W Jumper ring to tip 5V Zener Diode + to tip - to sleeve diagram |
Sleeve = S+B Tip = R Jumper ring to sleeve diagram |
Sleeve = S 6.8k resistor B to Sleeve Tip = R Jumper ring to sleeve diagram |
Sleeve = S+B Tip = R Jumper ring to sleeve Use W3 type headset diagram |
|
| Shure | S3 | UR1M | Lemo 3 pin | Pin3 = W Pin1 = S diagram |
Pin3 = R Pin1 = S+B diagram |
Pin3 = R Pin1 = S+B diagram |
Pin3 = R Pin1 = S+B Use W3 type headset diagram |
|
| Shure | SL | All with TA4F (Tiny QG) Connector, including UC1, FP1, PG1, PGX1, PGXD1, SLX1, ULX1, ULXD1, UR1, and UR1M | TA4F | Pin1 = S Pin3 = W 4.7k pin 2 to Pin 3 5V Zener Diode stripe end to Pin 3 other end to Pin 1 diagram |
Pin1 = S+B Pin3 = R 10k ohms 2 to 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin1 to pin 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin 1 to pin 3 Use W5 type headset diagram |
|
| Shure | AX | Axient System | TA4F | Pin1 = S Pin3 = W 12k pin 2 to Pin 3 5V Zener Diode stripe end to Pin 3 other end to Pin 1 diagram |
Pin1 = S+B Pin3 = R 15k ohms 2 to 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin1 to pin 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin 1 to pin 3 Use W5 type headset diagram |
|
| Shure | SU | U1L, UC1L | Lemo 4 pin | Pin4 = S Pin1 = W 6.8k ohms 1 to 2 diagram |
Pin4 = S Pin2 = R Pin1 = B jumper 1 to 3 diagram |
Pin4 = S Pin2 = R Pin1 = B jumper1 to 3 diagram |
Pin4 = S Pin2 = R Pin1 = B Jumper 1 to 3 Use W5 type headset diagram |
|
| Sky | SD | UT86P | 3.5mm locking plug | |||||
| Sony | DS | DWT-B01 | Hirose twist lock 4 pin | Pin 2 = W Pin 4 = S Jumper Pin 1 to Pin 3, 15k Resistor Pin 2 to Pin 3, 200pF Capacitor Pin 4 to Pin 3, 200pF Capacitor Pin 4 to Pin 2, Crimp fingers to shield diagram |
**Please see additional information** | Pin 1 = R Pin 2 = B Pin 4 = S 6.8k Resistor Pin 3 to Pin 4, 200pF Capacitor Pin 1 to Pin 4, 200pF Capacitor Pin 2 to Pin 4, Crimp fingers to shield diagram |
Pin 1 = R Pin 2 = B Pin 4 = S 10k Resistor Pin 3 to Pin 4, 200pF Capacitor Pin 1 to Pin 4, 200pF Capacitor Pin 2 to Pin 4, Crimp fingers to shield, Use W5 Type Headset. diagram |
|
| Sony | SO | WRT-820 | Hirose twist lock 4 pin | Pin4 = S Pin2 = W junper 1 to 3 1.8k ohms 2 to 3 diagram |
Pin4 = S+B Pin2 = R junper 1 to 3 1.8k ohms 2 to 3 diagram |
Pin1 = R Pin2 = B Pin4 = S 2.7k ohms 3 to 4 diagram |
Pin1 = R Pin2 = B Pin4 = S 2.7k ohms 3 to 4 Use W5 type headset diagram |
|
| Sony | SY | WRT-822, WRT-420, WRT-8B | Hirose twist lock 4 pin | Pin4 = S Pin2 = W 6.8k ohms 1 to 3 1.8k ohms 2 to 3 diagram |
Pin4 = S+B Pin2 = R 6.8k ohms 1 to 3 1.8k ohms 2 to 3 diagram |
Pin1 = R Pin2 = B Pin4 = S 2.7k ohms 3 to 4 diagram |
Pin1 = R Pin2 = B Pin4 = S 2.7k ohms 3 to 4 Use W5 type headset diagram |
|
| Sony | SN | WRT-805, UWP Series | 3.5mm locking plug | Tip = W Sleeve = S 6.8K ohms Tip to Ring 5V Zener Diode + to tip - to sleeve diagram |
Tip = B Ring = R Sleeve = S 10k resistor Tip to Sleeve diagram |
Tip = B Ring = R Sleeve = S 10k resistor Tip to Sleeve diagram |
Tip = B Ring = R Sleeve =S 10k resistor Tip to Sleeve Use W5 type headset diagram |
|
| Spokeman | MA | MA-2200 | 3.5mm non-locking mono plug | |||||
| Telex | TL | WT 200, WT400, WT450 | Lemo 4 pin | Pin 1 = S Pin 2 = W 6.8k ohms 2 to 3 diagram |
Pin 1 = S+B Pin 2 = R jumper 2 to 4 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R 10K ohms 1 to 2 diagram |
Pin 1 = S Pin 2 = B Pin 3 = R 10K ohms 1 to 2 diagram |
|
| Telex | TS | LT100, PST16, VB12, WT10, WT50, WT55, WT60, WT80, WT700, WT1000 | TA4F | Pin 1 = S Pin 2 = W 6.8k ohms 2 to 3 diagram |
Pin1 = S+B Pin2 = R 10k ohms 2 to 3 diagram |
Pin1 = S Pin2 = B Pin3 = R 10k ohms 1 to 2 diagram |
Pin1 = S Pin2 = B Pin3 = R 10k ohms 1 to 2 Use W5 type headset diagram |
|
| Toa | TA | WM4300 | TA4F | Pin 1 = S Pin 3 = W 1.5k ohms 1 to 3 Jumper 3 to 4 diagram |
Pin 1 = S+B Pin 4 = R diagram |
Pin 1 = S Pin 2 = R Pin 3 = B diagram |
Pin 1 = S Pin 2 = R Pin 3 = B Use W4 type Headset diagram |
|
| Toa | TO | WM370, WM4310 | Special Toa 3.5mm | Tip = W Sleeve = S diagram |
Tip = R Sleeve = S+B diagram |
Tip = R Sleeve = S+B diagram |
Tip = R Sleeve = S+B Use W4 type headset diagram |
|
| Trantec | SL | S5 | TA4F | Pin1 = S Pin3 = W 4.7k pin 2 to Pin 3 5V Zener Diode stripe end to Pin 3 other end to Pin 1 diagram |
Pin1 = S+B Pin3 = R 10k ohms 2 to 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin1 to pin 3 diagram |
Pin1 = Shield Pin2 = R Pin3 = B 22k pin 1 to pin 3 Use W5 type headset diagram |
|
| Vega | VL | 77, 677 | Lemo 4 pin | Pin1 = W Pin4 = S 2.7k ohms 1 to 2 200pf cap 1 to 4 diagram |
Pin 1 = B Pin 2 = R Pin 4 = S 200pF 1 to 4 200pf 2 TO 4 diagram |
Pin 1 = B Pin 2 = R Pin 4 = S 200pF 1 to 4 200pf 2 TO 4 diagram |
Pin 1 = B Pin 2 = R Pin 4 = S 200pF 1 to 4 200pf 2 TO 4 diagram |
|
| Vega | VS | T23, T25, T37, T93, Pro-2, BP2020, ST2020 | TA4F | Pin2 = W Pin4 = S Jumper 2 to 3 diagram |
Pin 2 = R Pin 4 = S+B diagram |
Pin 1 = R Pin 3 = B Pin 4 = S diagram |
Pin 1 = R Pin 3 = B Pin 4 = S diagram |
|
| Vocopro | VP | UHF-BP1 | TA3F | Pin 1 = W Pin 3 = S diagram |
Pin 1 = R Pin 3 = S+B diagram |
Pin 1 = R Pin 3 = S+B diagram |
Pin 1 = R Pin 3 = S+B Use W3 Type Headset diagram |
|
| Zaxcom | ZX | All with 3-pin Lemo
|
Lemo 3 pin | Pin3 = W Pin1 = S Pin 1 connected to shell diagram |
Pin3 = R Pin1 = S+B Pin 1 connected to shell diagram |
Pin3 = R Pin1 = S+B Pin 1 connected to shell diagram |
Pin3 = R Pin1 = S+B Use W3 type headset Pin 1 to shell diagram |
|
| Zaxcom | ZA | All with Lemo micro 4 pin | Lemo micro 4 pin | Pin 1 = S Pin 2 = W Jumper 1 to 4 2.2K ohms 2 to 3 200pF 1 to 2 200pF 3 to 4 diagram |
Pin 1 = S+B Pin 2 = R Jumper 1 to 4 2.2K ohms 2 to 3 200pF 1 to 2 200pF 3 to 4 diagram |
Pin 1 = S+B Pin 2 = R Jumper 1 to 4 2.2K ohms 2 to 3 200pF 1 to 2 200pF 3 to 4 diagram |
video title
video content